According to the HCIA-5G V2.0 Exam Outline, the statements in options A, B, and C are correct descriptions of throughput-related indicators, which correspond to options A, B, and C. The statement in option D is incorrect because adding the last small packet of each data transmission burst and its transmission duration will reduce the accuracy of throughput measurement.

According to the 5G NR Physical Layer Specifications, Paging, SIB, and MIB are common messages that need to be scheduled. Paging is a message that is used to notify a UE of incoming data or system information when it is in idle mode or connected mode inactive state. SIB stands for System Information Block, which is a message that contains various system parameters and configuration information for UEs. MIB stands for Master Information Block, which is a message that contains essential system information such as system frame number and subcarrier spacing. These common messages need to be scheduled because they are transmitted periodically and have fixed time-frequency resources.

According to the 5G NR Channels, the following logical channels can be mapped to different transport channels in the downlink and/or uplink:

• Common Control Channel (CCCH): It can be mapped to Downlink Shared Channel (DL-SCH) or Uplink Shared Channel (UL-SCH).
• Dedicated Control Channel (DCCH): It can be mapped to DL-SCH or UL-SCH.
• Paging Control Channel (PCCH): It can be mapped to Paging Channel (PCH) or DL-SCH.
• Broadcast Control Channel (BCCH): It can be mapped to Broadcast Channel (BCH) or DL-SCH.

According to the Hardware Description: Bbu5900 V100r013c10, these statements are correct about the space principles for 5G BBU installation:

• If the installation space is insufficient, the BBU can be installed on a wall. Ensure that the wall meets the load bearing requirements: The BBU can be installed on a wall using wall-mounted brackets. The wall must be able to bear at least four times the weight of the BBU and must be flat and vertical. The installation height of the BBU must not exceed 2 m.
• If the space is greater than 600 mm, a cabinet can be added to install the BBU: The BBU can be installed in a cabinet that meets the requirements of Huawei base stations. The cabinet must have a width of 19 inches and a depth of at least 600 mm. The cabinet must also provide sufficient ventilation, grounding, and lightning protection for the BBU.
• If the remaining space of an existing cabinet is greater than 4 U, the BBU can be installed directly: The BBU can be installed in an existing cabinet that has enough space for it. The BBU has a height of 2 U, so it requires at least 4 U of space in a cabinet. The existing cabinet must also meet the requirements of Huawei base stations.

The other statement is incorrect about the space principles for 5G BBU installation:

• If the installation space is insufficient, install 5G boards directly into the existing 4G B8U: This statement is not supported by Huawei base stations. The 5G boards cannot be installed directly into the existing 4G B8U because they have different slot distributions and board types. The 5G boards can only be installed in a BBU5900 subrack that supports both LTE and NR modes.

According to the HCIA-5G - Huawei Enterprise Support Community, reflection in a large amount of water and signals traveling far along a street due to the waveguide effect are common causes of overshoot coverage, which correspond to options A and C.

According to the Troubleshooting Guide for Huawei 5G Base Stations, the possible causes of SCTP link disconnection over the N2 interface are as follows:

• Routes are not configured: If the routes between the base station and the core network are not configured correctly, the SCTP link cannot be established or may be disconnected.
• PLMN configurations are incorrect: If the PLMN configurations on the base station and the core network do not match, the SCTP link cannot be established or may be disconnected.
• Physical ports are faulty: If the physical ports on the base station or the core network are faulty, such as damaged cables, loose connectors, or port errors, the SCTP link cannot be established or may be disconnected.
• The SCTP port configuration is incorrect: If the SCTP port configuration on the base station or the core network is incorrect, such as using a reserved port number or a conflicting port number, the SCTP link cannot be established or may be disconnected.

According to the Huawei’s Latest AAU Products, Huawei’s AAUs have an operating voltage of -48 V DC and support LTE-NR dual-mode on some frequency bands, such as C-band and sub-3 GHz bands. The article also states that Huawei’s new-generation 64T64R AAUs provide higher coverage gains than conventional 32T32R AAUs by using ELAA (extremely large antenna array) technology. Huawei’s AAUs do not support GSM-NR dual-mode on any frequency band, as GSM is not a compatible RAT with NR.

 According to the Career Certification - Huawei Enterprise, DUB8P, DUPEU, and DUMPT are boards in a base station that support CPU usage measurement, which correspond to options B, C, and D. DFAN is a fan board that does not support CPU usage measurement, which corresponds to option A.