Refer to the exhibit.

The http monitor is applied to a pool All members are enabled One pool member stops responding TCP port 80. The server still responds to ping.

What is the resulting status of this pool member?

An LTM Specialist needs to enable TCP connection re-use for a non-HTTP application. The application uses a simple request response protocol where each request and response is contained within a single packet.

Which configuration option should the LTM Specialist adjust?

Traffic to a pool of SFTP servers that share storage must be balanced by an LTM device.

What are the required profile and persistence settings for a standard virtual server?

A web server's default gateway is the network router. The LTM Specialist needs to introduce an LTM device to load balance to the web servers without changing the server's default gateway.

Which deployment method and settings should the LTM Specialist use to ensure correct traffic flow and that the web servers can obtain the actual con IP addresses?

A design requires the LTM device to become HA standby when the one of the two physical interface on the External trunk is down the External trunk is an interface on the External VLAN

Which TMOS command enables this behavior?

An LTM device receives a response string containing "error"

Which monitor type and parameter will mark the HTTP server as down?

An LTM Specialist needs to assign a health monitor to a pool with two pool members 10.10.10 101 and 10.10.10.102 Both pool members are listening on port 8080 with TCP. The health of the application depends on the health of an another server (10 10 10 100) that runs port 9080 with TCP.

Which two custom TCP monitors should be selected as the pool's health monitors' (Choose two)

An LTM Specialist needs to use a set of addresses to access an Internet website in an outbound configuration.

Which feature should the LTM Specialist configure?

Where does a LTM Specialist view all of the objects that are part of a deployed iApp?

Exhibit.

The server team has recently configured the three new DNS servers shown for the data center. No current DNS servers are currently configured on the LTM device.

Which command should be used to configure the LTM device to use the new DNS servers?

A virtual server is experiencing intermittent port exhaustion. What should be done to fix this issue?

An LTM Specialist needs to provide access to a 8BG-IP to device for a company's support person access to the BIG IP device, but are NOT allowed to change any settings All support the support remote access to the BIG-IP device, but are NOT allowed to change ant settings. All support have accounts in the company's Active Directory

Which method is appropriate to provide access for the support personnel to the BIG-JP device?

An LTM device configured with a management IP address and route and a series of self-IPs and TMM routes. Both management and TMM have a routing entry for 101 10/24 Application traffic is being load balanced and sent to pool member 10.1.1.123 with SNAT Automap and configured.

Which route will the LTM device use?

A custom TCP application using a single server is being migrated to the LTM device. A server is being added to the pool. The application is known to violate the TCP protocol RFC. The application currently works without error from a user perspective.

Which virtual server type is appropriate in this situation?

A virtual server with SNAT automap enabled selects pool member 10.20.0.10.443 for the server-side flow. The client side flow source IP is 192.168.0.10 .

Which source IP should be expected in the server-side connection?

An LTM Specialist has recently taken over administration or an LTM device that has experienced resource availability issues. The LTM device will need to be solely used for load balancing and SSL offload. Previously, the LTM device was also used to provide statistical analysis of application traffic. However, that functionality has been moved to a third party solution.

Based on the output below, which configuration change should be made to ensure the LTM module receives the most amount of resources?

An LTM Specialist needs to apply SNAT using currently used SNAT pool to a new virtual server.

What needs to be completed before applying that configuration change?

An SSL application is being migrated to the LTM device. Both encrypted and unencrypted traffic are accepted by the server. The virtual server configuration is as follows:

Which LTM device profile should be used on the LTM device to reduce the CPU load on the current.

An LTM Specialist needs to force only FTP traffic, sourced from subnet 10.10.10.0/24 to virtual server 10.10.20.1 to the new FTP1 server. The following virtual servers are configured on the LTM device:

Traffic sourced from 10.10.10/24 must use the specific pool member for load balancing.

Which configuration change is needed to meet the requirements?

An LTM Administrator receives an email from the NOC stating that the switch connected to the backend server was shut down for maintenance. The BIG-IP device handles only UDP traffic. The BIG IP device did not fail over to a DR location when no pool members were available.

When the LTM Administrator checks the pool, it confirms that the monitor is still marking UP the pool member.

A tcpdump of the traffic shows the following output:

A list of the monitor configuration shows the following:

Which two modifications to the LTM configuration will mark this pool member down, when the switch is down? (Choose two.)

An LTM Specialist needs to upgrade all guests on a Viprion eight CMP guests.

What is the maximum number of guests that the LTM Specialist should upgrade at once?

When importing a PEM formatted SSL certificate, which text needs to appear first in the file?